Additively manufactured Haynes-282 monoliths containing thin wall struts of varying thicknesses

Simple item page
dc.contributor.authorLim, Ben_AU
dc.contributor.authorChen, Hen_AU
dc.contributor.authorNomoto, Ken_AU
dc.contributor.authorChen, Zen_AU
dc.contributor.authorSaville, AIen_AU
dc.contributor.authorVogel, SCen_AU
dc.contributor.authorClarke, AJen_AU
dc.contributor.authorParadowska, AMen_AU
dc.contributor.authorReid, Men_AU
dc.contributor.authorPrimig, Sen_AU
dc.contributor.authorLiao, XZen_AU
dc.contributor.authorBabu, SSen_AU
dc.contributor.authorBreen, AJen_AU
dc.contributor.authorRinger, SPen_AU
dc.date.accessioned2024-02-26T07:24:29Zen_AU
dc.date.available2024-02-26T07:24:29Zen_AU
dc.date.issued2022-09-01en_AU
dc.date.statistics2022-10-17en_AU
dc.description.abstractMagnitude and distribution of residual stresses in additively manufactured Ni-based superalloys may impact the mechanical performance of as-fabricated parts. Though electron beam powder bed fusion (E-PBF) can produce components with minimal defects and residual stresses compared to laser powder bed fusion and directed energy deposition, variations of them may occur within the complex geometry of a component, due to inherent variations of thermal signatures and the evolution of section modulus along the build direction. This work reveals the residual stress distribution, characterised from neutron diffraction, of an as-fabricated Haynes 282 monolith containing internal cube voids and thin wall struts of varying thicknesses. Complementary local hardness measurements and multi-scale microscopy were used to investigate the geometry-structure-property relationships. Observed variations in hardness were attributed to a combination of type I macro-scale residual stresses and variations in bimodal γ′ precipitation behaviour. The results highlight the influence of residual stresses and microstructure on the mechanical properties of E-PBF Haynes 282. © 2022 The Author(s). Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND licenseen_AU
dc.description.sponsorshipThe authors acknowledg the facilities, the scientific, and technical assistance of the teams at Sydney Microscopy & Microanalysis (SMM) and the Sydney Manufacturing Hub, which are Core Research Facilities at the University of Sydney. SMM is the University of Sydney’s node of Microscopy Australia. Mr. James Dingle’s (University of Sydney) contribution to Figs. 2 and 12 are acknowledged. This research was sponsored by the Department of Industry, Innovation and Science under the auspices of the AUSMURI program which is a part of the Commonwealth’s Next Generation Technologies Fund. A/Prof. Sophie Primig is supported by the UNSW Scientia Fellowship scheme. Asst. Prof. Zibin Chen is supported by the Research Office of The Hong Kong Polytechnic University (Project code: P0039966 & P0039581). The contributions of Profs. Amy Clarke and Sudarsanam Suresh Babu were funded by the Department of the Navy, Office of Naval Research under ONR award number N00014-18-1-2794. Any opinions, findings, and conclusions or recommendations expressed in this material are those of the author(s) and do not necessarily reflect the views of the Office of Naval Research. The facilities and technical assistance of the teams at Oak-Ridge National lab are acknowledged for the fabrication of the E-PBF Haynes 282 builds. The research at Oak-Ridge National Laboratory was sponsored by the US Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office under contract DE-AC05-00OR22725 with UT-Battelle, LLC. Access to the Oak Ridge National Laboratory’s (ORNL) additive manufacturing equipment at ORNL’s Manufacturing Demonstration Facility (MDF) was facilitated by US Department of Energy’s Strategic Partnership Projects (SPP) mechanism. More information can be found at https://science.energy.gov/lp/strategic-partnership-projects. Mr. Alec Saville gratefully acknowledges the National Science Foundation Graduate Research Fellowship, USA, under Grant No. 2019260337 for supporting the analyses related to Fig. 4. Neutron diffraction measurements to generate Fig. 4 were supported by the Los Alamos Neutron Science Center (LANSCE), a NNSA User Facility operated for the US Department of Energy (DOE) by Los Alamos National Laboratory (LANL). LANL is operated by Triad National Security, LLC, for the National Nuclear Security Administration, USA, of US DOE (Contract No. 89233218CNA000001).en_AU
dc.identifier.articlenumber103120en_AU
dc.identifier.citationLim, B., Chen, H., Nomoto, K., Chen, Z., Saville, A. I., Vogel, S., Clarke, A. J., Paradowska, A., Reid, M., Primig, S., Liao, X., Babu, S. S., Breen, A. J., & Ringer, S. P. (2022). Additively manufactured Haynes-282 monoliths containing thin wall struts of varying thicknesses. Additive Manufacturing, 59, 103120. doi:10.1016/j.addma.2022.103120en_AU
dc.identifier.issn2214-8604en_AU
dc.identifier.journaltitleAdditive Manufacturingen_AU
dc.identifier.urihttps://doi.org/10.1016/j.addma.2022.103120en_AU
dc.identifier.urihttps://apo.ansto.gov.au/handle/10238/15434en_AU
dc.identifier.volume59en_AU
dc.language.isoenen_AU
dc.publisherElsevieren_AU
dc.relation.urihttps://doi.org/10.1016/j.addma.2022.103120en_AU
dc.subjectHardnessen_AU
dc.subjectResidual stressesen_AU
dc.subjectNeutron diffractionen_AU
dc.subjectHeat resisting alloysen_AU
dc.subjectNickelen_AU
dc.subjectDefectsen_AU
dc.subjectHaynes alloysen_AU
dc.titleAdditively manufactured Haynes-282 monoliths containing thin wall struts of varying thicknessesen_AU
dc.typeJournal Articleen_AU
Files
Original bundle
Now showing 1 - 2 of 2
Thumbnail Image
Name:
1-s2.0-S2214860422005097-main.pdf
Size:
12.61 MB
Format:
Adobe Portable Document Format
Description:
Download
Thumbnail Image
Name:
1-s2.0-S2214860422005097-mmc1.pdf
Size:
484.03 KB
Format:
Adobe Portable Document Format
Description:
Download
License bundle
Now showing 1 - 1 of 1
Thumbnail Image
Name:
license.txt
Size:
1.63 KB
Format:
Item-specific license agreed upon to submission
Description:
Download
Collections
Journal Articles