Browsing by Author "Guo, Q"
Now showing 1 - 4 of 4
Results Per Page
Sort Options
- ItemIndividual dispersion of carbon nanotubes in epoxy via a novel dispersion-curing approach using ionic liquids(Royal Society of Chemistry, 2013-01-01) Hameed, N; Salim, NV; Hanley, TL; Sona, M; Fox, BL; Guo, QThe effective dispersion of carbon nanotubes (CNTs) in a thermoset was achieved using ionic liquid as the dispersion-curing agent. We preferentially dispersed multiwalled carbon nanotubes (MWCNTs) down to individual tube levels in epoxy resin. Here the dispersion is ruled by the depletion of physical bundles within the MWCNT networks, for which molecular ordering of ionic liquids is considered responsible. The quantitative analyses using ultra small angle X-ray scattering (USAXS) confirmed the dispersion of individual MWCNTs in the matrix. The distance between the dispersed nanotubes was calculated at different nanotube loadings using the power law fitting of the USAXS data. The fine dispersion and subsequent curing, both controlled by ionic liquid, lead to composites with substantially enhanced fracture mechanical and thermomechanical properties with no reduction in thermal properties. Merging processing techniques of nanocomposites with ionic liquid for efficient dispersion of nanotubes and preferential curing of thermosets facilitates the development of new, high performance materials. © 2013, Royal Society of Chemistry
- ItemMicrophase separation through competitive hydrogen bonding in double crystalline diblock copolymer/homopolymer blends.(American Chemical Society, 2010-09-28) Salim, NV; Hanley, TL; Guo, QMicrophase separation induced by competitive hydrogen bonding interactions in double crystalline diblock copolymer/homopolymer blends was studied for the first time. Poly(ethylene oxide)-block-poly(ε-caprolactone) (PEO-b-PCL)/poly(4-vinylphenol) (PVPh) blends were prepared in tetrahydrofuran. The diblock copolymer PEO-b-PCL consists of two immiscible crystallizable blocks wherein both PEO and PCL blocks can form hydrogen bonds with PVPh. In these A-b-B/C diblock copolymer homopolymer blends, microphase separation takes place due to the disparity in intermolecular interactions; specifically, PVPh and PEO block interact strongly whereas PVPh and PCL block interact weakly. The TEM and SAXS results show that the cubic PEO-b-PCL diblock copolymer changes into ordered hexagonal cylindrical morphology upon addition of 20 wt % PVPh followed by disordered bicontinuous phase in the blend with 40 wt % PVPh and then to homogeneous phase at 60 wt % PVPh and above blends. Up to 40 wt % PVPh there is only weak interaction between PVPh and PCL due to the selective hydrogen bonding between PVPh and PEO. However, with higher PVPh concentration, the blends become homogeneous since a sufficient amount of PVPh is available to form hydrogen bonds with both PEO and PCL. A structural model was proposed to explain the self-assembly and microphase morphology of these blends based on the experimental results obtained. The formation of nanostructures and changes in morphologies depend on the relative strength of hydrogen bonding interaction between each block of the block copolymer and the homopolymer. © 2010, American Chemical Society
- ItemNanofibrillar micelles and entrapped vesicles from biodegradable block copolymer/polyelectrolyte complexes in aqueous media(ACS Publications, 2013-07-09) Salim, NV; Hameed, N; Hanley, TL; Waddington, LJ; Hartley, PG; Guo, QHere we report a viable route to fibrillar micelles and entrapped vesicles in aqueous solutions. Nanofibrillar micelles and entrapped vesicles were prepared from complexes of a biodegradable block copolymer poly(ethylene oxide)-block-poly(lactide) (PEO-b-PLA) and a polyelectrolyte poly(acrylic acid) (PAA) in aqueous media and directly visualized using cryogenic transmission electron microscopy (cryo-TEM). The self-assembly and the morphological changes in the complexes were induced by the addition of PAA/water solution into the PEO-b-PLA in tetrahydrofuran followed by dialysis against water. A variety of morphologies including spherical wormlike and fibrillar micelles, and both unilamellar and entrapped vesicles, were observed, depending on the composition, complementary binding sites of PAA and PEO, and the change in the interfacial energy. Increasing the water content in each [AA]/[EO] ratio led to a morphological transition from spheres to vesicles, displaying both the composition- and dilution-dependent micellar-to-vesicular morphological transitions. © 2013, American Chemical Society.
- ItemReactive block copolymer modified thermosets: highly ordered nanostructures and improved properties(Royal Society of Chemistry, 2010-12-21) Hameed, N; Guo, Q; Xu, ZG; Hanley, TL; Mai, YWA highly ordered poly(dimethyl siloxane)-poly(glycidyl methacrylate) (PDMS-PGMA) reactive diblock copolymer was synthesized and used to modify bisphenol A-type epoxy resin (ER). The PDMS-PGMA block copolymer consisted of epoxy-miscible PGMA blocks and an epoxy-immiscible PDMS block. The PGMA reactive block of the block copolymer formed covalent bonds with cured epoxy and was involved in the network formation, and the PDMS block phase separated to give different ordered and disordered nanostructures at different blend compositions. The solvent cast PDMS-PGMA diblock copolymer showed ordered hexagonal cylindrical morphology. A highly ordered morphology consisting of hexagonal cylinders inside the lamellar morphology was observed in the cured PDMS-PGMA block copolymer. In the cured ER/PDMS-PGMA blends, a variety of morphologies including lamellar, cubic and worm-like and spherical nanostructures were detected depending on the blend composition. Moreover, the addition of this reactive diblock copolymer significantly increases the hydrophobicity and the glass transition temperature. It also improves the tensile strength and tensile ductility of the nanostructured thermosets at low diblock copolymer contents. © 2010, Royal Society of Chemistry